Showing posts with label Pixhawk. Show all posts
Showing posts with label Pixhawk. Show all posts

Thursday, February 9, 2017

Reach and Pixhawk Integration in a Tuffwing UAV Mapper

By Ian Gates of Tuffwing and Texas A&M Agrilife Extension, Brian Christal of Tuffwing. Posted by Stephanie Pelczar.

The Reach Module captures precise event locations of a UAV in flight when the onboard camera is triggered. The Reach is not used for flight navigation. Read the following for instructions on Reach and Pixhawk integration in a Tuffwing UAV Mapper.

Items needed:
1. Find an open AUX servo plug on the end of the Pixhawk. Make sure to only use one of the AUX OUT plugs and ensure that there are now signals being sent to it from the Pixhawk (found under Full Parameter Tree in Mission Planner).

2. Find the end of your Reach hot shoe time mark cable with the male servo plug. Insert into the open AUX OUT port you have chosen to use in step 1. Note the black wire or (-) should be on top- not the white wire.

3. Insert the hot shoe circuit board with the small pin facing towards the camera into the camera's hot shoe adapter. Be careful when inserting and removing hot shoe circuit board as the small pin might get hung up.

4. The remaining end of the Reach hot shoe time mark cable has a DF-13 6-pin connector on it. You must pay close attention while inserting/removing this plug into a Reach Module as it is fragile and easily damaged. Find the DF-13 6-pin plug receptacle on the side of the Reach Module that has the Edison chip. (It should be the side of the board with only one plug on the entire face.)

5. Take the Tallysman TW 4721 antenna and adhere it to the ground plane that you will be using for your aircraft. Ensure it is secure to avoid damage from motor propellor. Once you have it attached, take the end wth the pin and connect it to the appropriate port on the Reach Module.

6. Place the Reach Module in a safe/secure location within the aircraft to prevent it from becoming unplugged during the flight.

7. Turn the Pixhawk on; ensure the Reach Module is receiving power. ###


More about the Tuffwing-Reach Hot Shoe Integration Cable

The Tuffwing-Reach hot shoe cable connects to your camera's hot shoe, powers your Reach rover, and adds time marks to your Reach event files. The time marks can be converted into geotags for creating precise maps.

Installation

1. Plug the male servo lead into anyopen port on your Pixhawk. The cable is for 5 volt power only. No communication occurs between the Pixhawk and the Reach. You can also power your Reach with a 5 volt UBEC.

2. Plug the hot shoe cable into your camera's hot shoe. You can use this hot shoe adapter if you have a Sony Nex 5 camera.


3. Plug the DF13 cable into the corner on the opposite side of the micro USB connector.

4. Set the antenna on a ground plane as close to the camera lens as possible.

Notes

  • No further configuration for the Reach hot shoe cable is required. Your camera will automatically trigger the hot shoe and the Reach will automatically record events.
  • Plug your hot shoe cable in once and disconnect using the servo connectors to prevent wear on the Reach Module's delicate DF13 connectors.
  • The hot shoe cable is compatible with all "standard" hot shoes.


Monday, January 30, 2017

Triggering and Geotagging with FLIR Vue Pro and Pixhawk.

By Brian Christal and Stephanie Pelczar


FLIR Vue Pro Set Up:

1. Install FLIR UAS on your Android or Iphone.
2. Power your FLIR Vue Pro camera with a mini USB cable.
3. Enable BlueTooth and start FLIR UAS.
4. Move the STILL slider to the left to select Single. 
Then select the Settings button (bottom right).



5. Select the MAIN tab.
6. Select IR Format to 14-bit TIFF Sequence.
7. Set Still File Type to 14-bit TIFF.
      
Note: These images will appear black when you view them. You must process them in an application like PIX4D to view them properly.





8. Select the ACCY. port tab.
9. Set Channel 3: to RECORD START/STOP.























Pixhawk Settings:

1. Start Mission Planner, connect your Pixhawk, then select INITIAL SETUP> Optional Hardware> Camera Gimbal.







2. Configure your Pixhawk as shown. RC9 can be any open port in the list.


Connect your FLIR Vue Pro to the Pixhawk.


1. Connect your FLIR Accessory cable or Tuffwing FLIR Trigger Cable as shown. 

Note: The FLIR trigger cable does not provide power. You must power the FLIR with a mini USB cable.

The servo cable can go in any RC Out port you chose in the previous step.

A special mini USB cable is also required to power the camera. You must provide 5 volts of power to the back of the Pixhawk. FLIR Vue Pro thermal cameras require 1.2 watts at 5 volts. This can be provided by your airplane's ESC or a BEC.



Install the camera mount.

1. Unscrew the lens ring from your FLIR Vue Pro.
2. Insert your FLIR Vue Pro through the mount and screw the lens on.









3. Place the mount in your UAV Mapper.























4. Right-click on the map and select Trigger Camera NOW. If everything is set up correctly, your Pixhawk will trigger the Canon camera to take pictures and is capable of triggering pictures using GPS distance.